How to Make a Building Airtight: Tapes & Sealing Explained

You can fit all the insulation you like, but if air is still finding its way through gaps, joints and penetrations, you’re not getting the full benefit from it.

And air has an annoying habit of finding the bits you’ve missed.

Good airtightness comes down to creating a continuous sealed layer around the building. That means paying attention to membrane overlaps, windows and doors, service penetrations and all the other little gaps that can quickly add up.

Here’s where tapes and seals come into it.

What Does Airtightness Actually Mean?

Put simply, an airtight building limits uncontrolled air leakage through the building envelope.

We’re not talking about stopping all ventilation. Buildings still need properly designed ventilation.

The aim is to stop air getting in and out where it isn’t supposed to.

That can help reduce unwanted draughts and heat loss while allowing the building’s ventilation system to do its job properly.

The tricky part?

Your airtight layer is only as good as its weakest point.

Where Do Air Leaks Usually Happen?

The big areas are rarely the problem. It’s normally the details.

Common areas to keep an eye on include:

  • Membrane overlaps and joints
  • Around windows and doors
  • Service penetrations
  • Pipework and cables
  • Junctions between different materials
  • Gaps around frames
  • Tears or damage in membranes
  • Floor, wall and ceiling junctions

One small gap might not look particularly dramatic. Multiply those little gaps across an entire building and you’ve suddenly got plenty of places for air to travel.

That’s why airtightness is all about continuity.

Sealing Membrane Overlaps and Joints

If you’re installing an airtight membrane or vapour control layer, every overlap and joint needs to become part of the continuous airtight layer.

This is where single sided airtight tape comes in.

It’s applied over overlaps and joints to create a continuous seal across the membrane.

It can also be used around penetrations and other areas where the airtight layer has been interrupted.

The important thing is making sure the tape is properly bonded to a clean surface and isn’t relying on a dusty or poorly prepared substrate to stay in place.

Because the best airtight tape in the world can’t do much if it’s stuck to a layer of building dust instead of the actual membrane.

[Walther Strong Single Sided Airtight Tape]

What About Double Sided Airtight Tape?

Double sided airtight tape does a slightly different job.

Rather than sitting visibly over the top of a joint, it can be used between membranes or substrates, allowing you to bond and seal the materials together.

This makes it particularly useful where you want the airtight connection hidden within the construction.

So the easiest way to remember it is:

  • Single sided = seal over the joint.
  • Double sided = bond between the materials.

Same overall goal. Different way of getting there.

[Walther Strong Double Sided Airtight Tape]

Sealing Around Windows and Doors

Windows and doors are obvious weak points because you’re introducing a frame into an otherwise continuous building envelope.

Even when a frame looks tightly fitted, small gaps around the perimeter can allow unwanted air through.

One option for these areas is Self Expanding Foam Tape.

It’s applied in a compressed state and then gradually expands to fill the gap, creating a weather and airtight seal around the frame.

Walther Strong Self Expanding Foam Tape can expand from 5mm up to 35mm and is suitable for internal and external applications.

It’s particularly handy for irregular gaps where trying to create a neat seal with a conventional tape isn’t practical.

Fit it. Let it expand. Let it do its thing.

[Walther Strong Self Expanding Foam Tape]

Don’t Forget Service Penetrations

Pipes, cables and other services have to pass through walls, ceilings and membranes somewhere.

Unfortunately, every time something passes through your airtight layer, you’ve potentially created another route for air leakage.

These areas need to be properly sealed rather than leaving a small gap around the penetration and assuming it won’t matter.

A suitable airtight tape can be worked around penetrations to reconnect the membrane and maintain the seal.

It’s one of those small jobs that’s easy to overlook when you’re trying to get everything else finished, but airtightness testing has a habit of finding the bits everyone forgot about.

Junctions Matter Too

Walls don’t exist on their own.

They meet floors, ceilings, roofs, windows, doors and other walls, and every one of those junctions needs consideration when you’re creating the airtight layer.

Think of airtightness as drawing one continuous line around the inside of the building.

Every time that line stops, changes material or has something passing through it, ask:

How is this bit being sealed?

It’s a simple way of spotting potential problem areas before they’re covered up.

Airtight Doesn’t Mean Unventilated

This one’s worth clearing up.

Making a building airtight does not mean sealing everything up and hoping nobody opens a door again.

Airtightness is about controlling unwanted air leakage.

Ventilation is about providing planned air movement.

They’re two different things.

A well designed building can have a high level of airtightness while still providing the ventilation needed for indoor air quality and moisture management.

Common Airtightness Mistakes

Most problems aren’t particularly complicated. They’re usually small details that have been missed.

Watch out for:

  • Leaving membrane overlaps untaped
  • Using a tape that isn’t designed for airtight applications
  • Applying tape to dusty or damp surfaces
  • Forgetting penetrations around pipes and cables
  • Missing junctions between different materials
  • Leaving gaps around window and door frames
  • Damaging a membrane after it’s already been sealed
  • Assuming a tiny gap won’t make a difference

And if another trade comes along afterwards and puts a hole through your beautifully sealed membrane?

Well… that’s always a fun conversation.

Which Airtightness Product Do You Need?

Here’s the quick version.

Job Product
Sealing membrane overlaps and joints Single Sided Airtight Tape
Sealing around penetrations Single Sided Airtight Tape
Bonding membranes together with a hidden seal Double Sided Airtight Tape
Sealing suitable gaps around windows and doors Self Expanding Foam Tape

There isn’t one tape that needs to do everything.

The important part is choosing the right sealing method for each detail and making sure they all connect to create one continuous airtight layer.

Airtightness Is All in the Details

Airtightness isn’t about one massive job.

It’s about getting lots of small details right.

Seal your membrane overlaps. Deal with penetrations. Pay attention to junctions. Don’t forget around windows and doors. And make sure the products you’re using are actually designed for the job.

Because air doesn’t care that you’ve got 99% of the building perfectly sealed.

It’ll find the other 1%.

Explore the Walther Strong Airtightness & Sealing range

Enquire about this product